In this case the bit One HD Virtuoso processor must be connected to the PC and turned on. The connection between PC and bit One HD Virtuoso can be established via USB.
When switched on for the first time the product uses the filters on the IIR output channels by default, but it is then possible to select the FIR mode. Firmware 3.0 allows you to select these two operating modes using a single Firmware.
At this point it is necessary to know in advance the system that you intend to implement, since later, to modify these selections, you will have to run the guided procedure again.
Below is the check list to follow for the complete configuration of your bit One HD Virtuoso.
|
SETUP |
OPERATION |
REFERENCE |
|
1 |
Connect the Master inputs of the bit One HD Virtuoso to the outputs of your audio system source. During this operation it is advisable to disconnect the RCA / AD LINK - AC LINK sockets of the bit One HD Virtuoso, connected to the amplifiers. |
See Sec. 5 |
|
2 |
Connect the bit One HD Virtuoso to the PC, switch on the audio system. |
|
|
3 |
Open the bit One HD Virtuoso Pc software previously installed in the PC. |
|
|
4 |
Start the config “I/O CONFIGURATION WIZARD”. |
|
|
5 |
Set the filters of all the bit One HD Virtuoso output channels according to the characteristics of your speakers. |
|
|
6 |
Set the bit One HD Virtuoso time delays manually. |
|
|
7 |
Finalize the bit One HD Virtuoso. Exit the PC Software and turn off the system. Reconnect the Bit One HD outputs to the amplifiers, and restart the system and PC software. |
|
|
8 |
Select through the "solo" function all the speakers that make up the FRONT Left, and adjust the output levels, the polarity. Perform this operation for the FRONT Right, REAR Left, REAR Right. Enable via the “solo” function only the SUBWOOFER channel(s), together with the previously adjusted fronts and perform its level calibration, phase. To perform a calibration of the output levels it is advisable to perform an RTA of the system via bit Tune. (see sec 8.8.4) |
|
|
9 |
Select Input eq and optimize the input equalization curve and the possible presence of ALL PASS. If the DE-EQ / Phase Adjustement has been carried out, it will be possible to intervene on the results and further refine them. |
|
|
10 |
Select all the speakers of the FRONT and through an RTA and PINK NOISE, set the output channels levels, Polarity and CHANNELS EQ equalization. (see sec 8.8.4) |
|
|
11 |
Select all the speakers of the REAR and through an RTA and PINK NOISE, set the levels of the output channels, Polarity and equalization CHANNELS EQ. |
|
|
12 |
Make the whole system play and through an RTA and PINK NOISE, set the levels of the output channels, Polarity and equalization. |
|
|
13 |
Select MAIN EQ and set the desired frequency response, depending on the preferred acoustic approach. |
|
|
14 |
Use the BASS BOOST function to set the low frequency response. |
|
|
15 |
By listening to your favorite music, you can further refine your system by intervening at points 9 ÷ 13. |
|
|
16 |
*Copy the current memory to the other memories to create starting bases for other setups, or select a new memory and repeat points 10 ÷ 15. |
|
|
17 |
FINALIZE THE BIT ONE HD |
*Remark: in the case of the Pass through, only one memory linked to the Master input will be available and it will not be possible to copy this memory to the other remaining and vice versa. The other available memories will be available for the other AUX, Optical 1/2 inputs available.
￭ PC software turn on in CONNECT MODE:
Upon turn on, if correctly interfaced with the PC (software and drivers installed correctly), the device will show the communication window as shown in the figures to the side.
If at the end of the scanning the bit One HD Virtuoso is not found:
- check that the bit One HD Virtuoso is switched on (Audison logo light on);
- check that the USB cable is connected correctly;
- press OK to search for the device again;
- press CANCEL to start the OFFLINE mode.
In the default configuration, the bit One HD Virtuoso is configured as shown below:
Input Hi Level Master:
- CH1 Front Left Full
- CH2 Front Right Full
- CH3 Rear Left Full
- CH4 Rear Right Full
AUTO TURN ON Hi Level: enabled
Output Analog (Pre Out):
- CH1: Front Left Woofer -CH2: Front Right Woofer.
- CH3: Front Left Midrange -CH4: Front Right Midrange.
- CH5: Front Left Tweeter -CH6: Front Right Tweeter.
- CH7: Rear Left Woofer -CH8: Rear Right Woofer.
- CH9: Rear Left Tweeter - CH10: Rear Right Tweeter.
- CH11: Center Tweeter - CH12: Center Woofer.
- CH13: Subwoofer.